Why do washing machines shake

Turning these legs should raise or lower them depending on the direction. These struts may break, or otherwise weakened; thus, encouraging greater movement when the washing machine enters the spin cycle. A quick visual inspection of the interior components should reveal any problems associated with the shock-absorbing struts.

Another possible cause of a shaking washing machine is broken or damaged suspension springs. These springs are used to suspend the basket from the frame. If they are broken or damaged, however, the washing machine may shake violently when it enters the spin cycle. Assuming you have a front-loading washing machine recommended for energy-efficiency , you can access the suspension springs through the top panel.

Overloading a washing machine with an excess amount of clothes and garments may also lead to shaking. I know most people are eager to wash their clothes in the fewest loads possible, but overloading a washing machine can lead to serious damage. Only fill your machine with the amount of clothes recommended by the manufacturer.

You must be logged in to post a comment. Fred's Appliance. Lift the washer and put a block of wood under the bottom of the front. Shut the water lines and turn the electricity off by unplugging your machine. Pull your machine 2—3 feet 0. Tilt the machine so that the front legs lift off of the floor and the slide a block of wood under the front of the machine.

Let your machine back down slowly so that it rests on the block. Turn the bolts on the legs with a wrench to adjust the front legs. Start by adjusting the leg that is higher. Use a wrench or channel locks to loosen the bolt on the top of the leg by turning it counterclockwise.

Then, turn the base of the leg clockwise to raise it by twisting it. Tighten the bolt above the base of the leg to lock it in place. Use channel locks or a wrench to turn the bolt near the top of the leg clockwise. Turn it until it is tight against the base of your machine.

This will lock the leg and keep it from moving when you lower it. Lower your washing machine and check the spirit level again. Slide the wood block out and slowly lower the machine back down. Put your level back on top of your machine and check the air bubble to see if it is level.

If it is, try wobbling your machine again. If it wobbles and the front is level, you have to adjust the legs in the back. Place the level on the control panel at the back to check the back legs.

If your machine is more than 10 years old though, this may not be the case. Place your level flat on top of the control panel near the back of the machine. If the bubble is centered, your back legs do not need to be readjusted. There may be a little rust or dirt stuck in the self-leveling joint. If your control panel is round on top or set at an angle, place your level directly in front of it. Use the same process you used with the front legs to adjust the back legs.

Use the level to determine which leg is higher. Lift the machine up a little bit and slide a piece of wood underneath. Adjust the higher leg in the back to make it lower using the same bolt and tools that you used on the front. If you tilt your machine and discover that your back legs are indeed self-adjusting, lint and rust may have built up on the rear legs to keep them from moving. Tap the exposed legs lightly with the back of your wrench or channel locks to shake the rust and dirt off.

Lower the machine and try running an empty cycle. Remove the wooden block and lower your machine back down. If it continues to shake, you probably need to replace the shock absorbers. Method 3. Contact your manufacturer and order some replacement shock absorbers. They also connect the drum to the frame of the machine. There are either 2, 4, or 5 of them depending on your model. The model and brand are usually listed on the front, but they may be printed on a metal plate on the back of the machine or inside of the door.

Some newer models require a professional to install new shock absorbers. Disconnect the water and turn off the electricity. Find the supply lines for cold and hot water on the back of your machine. Twist the valve on each line so that it is closed.

Turn the electricity for your machine off by unplugging it. The water lines are usually thin and made of rubber. They often have a blue and red valve on top of them near the connection to the frame.

Remove the front panel for a front-load washer. Usually this involves removing the rubber seal around your drum and unscrewing several screws under the panel before lifting it up. Hook it back into the center of your drum and put the machine back. This was causing the noise and shaking. Unscrew the shock absorbers with a wrench or channel locks. Find the shock absorbers by looking for rods connecting the drum to the frame.

Unscrew the bolts connecting each rod to the drum and frame. Remove your rods and set them aside. They may not appear to be broken, but the inner coil in one of these absorbers may be broken. Some shock absorbers have pins locking them to the drum and the frame. If any of the pins fell out, simply slide them back in. This was probably the cause of your shaking. If you have 5 absorbers, 1 of them is probably in the back.

You may not be able to reach this piece without professional assistance. Insert your new shock absorbers and tighten them. Put your replacement parts in the corresponding locations. Reinstall the panels and run a test wash. Put your panel back and screw in the corresponding screws. Put the rubber seal back and open your water lines.

Plug the machine in and set it to run a basic wash cycle. If you hear rattling inside the machine, you probably missed a bolt for a shock absorber. Replacing the drum in a washing machine is often not worth it, and you should consult a washing machine repair company to determine the price of the repair.

It is not typically a problem that a non-professional can solve. What should I do if my front-loading washing machine is stuck in the rinse cycle? The rinse cycle is the point in a wash where the machine utilizes cold water. If your machine keeps running on the rinse cycle, it's a sign that your cold water connection is clogged and your machine keeps running while it tries to pull in enough water.

Close the connection on the water supply line by turning the valve and remove the line to see if it's damaged or clogged. Either replace the line or remove the blockage to see if that solves your problem.

Not Helpful 0 Helpful 4. Remove any dirt, hair or foreign object from the filter. Then give it a rinse under the tap. Inspect the filter cavity to see if anything like dirt, coins or buttons are stuck in it. Give it a wipe with a damp cloth. Finally, replace and secure the filter by turning it clockwise, and pop the kickplate cover back on. Thank you for your feedback.

You just added this product to your wishlist. You just removed this product from your wishlist. You can't add more to wishlist. Are you sure you want to clear your wishlist? You can only compare products from the same category. You just added an item to compare! Keep going! You just removed an item to compare! Your compare list is full! You only added 1 product. Please add more products to compare. Support Help Center Warranty.